15 Rock On Sasquatch with American Flag Cornhole Board Decal Kit
$33.00
/
Shipping calculated at checkout.
Pickup available at 1795 M-32
Usually ready in 24 hours
THIS IS FOR A SET OF DECALS ONLY (2 decals included) - NO BOARD OR COATING INCLUDED
This is a basic sticker, without any lamination to protect from the elements. It is advised (for the longevity of the material) to seal in with a couple of coats of Polyurethane.
The edge strip kit is available with white, black, red, or blue stripes. Sasquatch design is available with a white or black squatch.
The standard kit only includes the 2 sasquatch decals (sized roughly at 15"h x 11.5"w).
The Edge Strip kits also contain 4 stripes, all approximately 2"w and set to fit regulation 2'x4' boards.
All pieces included will be separate sticker pieces with backing, they will not arrive all in one square.
**We are not responsible for the loss of decals that are personally installed.**
Works well on – Walls, Glass, Plastic, Tile, Metal, Painted wood (after 3 months), and other smooth services.
Transfer tape/Application Mask will be on each decal ordered, for an easy transfer. (stripes will not have application mask)
~~~APPLICATION DIRECTIONS:~~~
1. Clean the surface area where the decal will be applied with alcohol and water. (This is a DRY install so please do not spray 'bare' wood before install, just be sure area is clean from any debris and sawdust that will affect the sticking).
2. Adhere the extra strip of application mask on top of your decal, to establish the exact location.
3. Measure location to make sure the decal is centered and straight (measure from the actual decal, not the paper backing. It is not guaranteed that the paper will be straight).
4. Slowly remove the paper backing, starting with the top, while smoothing the decal side to side with a scraper or credit card.
5. Apply the decal to your surface and smooth (again) with a credit card.
6. Remove the application mask carefully. Some areas may need to be scraped down again.
**When placing the decal on a vehicle, try to place out of the way of the vehicle wipers. Wiper blade use over a decal can lift edges causing moisture to get underneath and lift/ruin your decal.
*Absolutely NO POWER WASHING or high pressure washing over the decal once installed. This can also cause edges to lift and the moisture will ruin the adhesive under the decal.
You will be provided with these instructions also in your package, and a small sample vinyl decal to practice the application with.
This is a basic sticker, without any lamination to protect from the elements. It is advised (for the longevity of the material) to seal in with a couple of coats of Polyurethane.
The edge strip kit is available with white, black, red, or blue stripes. Sasquatch design is available with a white or black squatch.
The standard kit only includes the 2 sasquatch decals (sized roughly at 15"h x 11.5"w).
The Edge Strip kits also contain 4 stripes, all approximately 2"w and set to fit regulation 2'x4' boards.
All pieces included will be separate sticker pieces with backing, they will not arrive all in one square.
**We are not responsible for the loss of decals that are personally installed.**
Works well on – Walls, Glass, Plastic, Tile, Metal, Painted wood (after 3 months), and other smooth services.
Transfer tape/Application Mask will be on each decal ordered, for an easy transfer. (stripes will not have application mask)
~~~APPLICATION DIRECTIONS:~~~
1. Clean the surface area where the decal will be applied with alcohol and water. (This is a DRY install so please do not spray 'bare' wood before install, just be sure area is clean from any debris and sawdust that will affect the sticking).
2. Adhere the extra strip of application mask on top of your decal, to establish the exact location.
3. Measure location to make sure the decal is centered and straight (measure from the actual decal, not the paper backing. It is not guaranteed that the paper will be straight).
4. Slowly remove the paper backing, starting with the top, while smoothing the decal side to side with a scraper or credit card.
5. Apply the decal to your surface and smooth (again) with a credit card.
6. Remove the application mask carefully. Some areas may need to be scraped down again.
**When placing the decal on a vehicle, try to place out of the way of the vehicle wipers. Wiper blade use over a decal can lift edges causing moisture to get underneath and lift/ruin your decal.
*Absolutely NO POWER WASHING or high pressure washing over the decal once installed. This can also cause edges to lift and the moisture will ruin the adhesive under the decal.
You will be provided with these instructions also in your package, and a small sample vinyl decal to practice the application with.